In case you didn’t know, a flow restrictor is equipped on almost every shower head that you can find on the market nowadays. This tool is specially designed to regulate the flow of water that comes through the shower head.
Anyhow, the flow restrictor usually lowers the PSI which results in loss of water pressure. This way, you are able to save a lot of water because you are simply using less. But, what happens when you don’t have strong water pressure and the flow restrictor is lowering it even more?
Well, you get pretty poor water pressure that makes your shower head basically useless. So, the only thing to do is to remove flow restrictor from a shower head.
In that light, let’s see how to remove flow restrictor from a Peerless shower head.
Peerless Shower Head – Flow Restrictor Problems
As we already said, Peerless shower heads are usually manufactured with the flow restrictor inside them. They are limiting the flow of water down to 2.5 gallons per minute and that is sometimes pretty low.
So, if you have poor water pressure and you simply can’t find the cause, we strongly suggest that you remove the flow restrictor from your Peerless shower head.
Now, the Peerless shower head is luckily easy to disassemble, and therefore, you’ll not have any troubles locating and removing the flow restrictor.
Anyway, let’s see how to remove a flow restrictor from your Peerless shower head. Let’s begin.
How to Remove Flow Restrictor from Peerless Shower Head
All you need to do to remove a flow restrictor from a Peerless shower head is to follow these next few steps and to gear up. The equipment that you need is some of the usual items you use inside your household.
But, let’s see exactly what you need:
- A screwdriver
- An old piece of cloth
- An adjustable wrench
Once you gather all this stuff, it’s time to get down to business. So, let’s begin with the steps.
Step 1 – Remove the Peerless shower head from the faucet
As you could suspect, the first thing to do is to remove the Peerless shower head from its base, the faucet. Since you will spend most of the time looking inside the Peerless shower head pipe, it’s quite important to clean any kind of debris you find inside the shower head.
Once you remove it from the faucet, use an old piece of cloth to clean the shower head insides a bit. This way, you will more likely be able to finish this job faster.
Anyhow, if you have any troubles with the removal of the shower head from the faucet, we recommend using an adjustable wrench. This way, by turning it counter-clockwise, you’ll definitely disconnect it from the faucet.
Step 2 – Inspect the Peerless shower head
Here, you’ll need to determine where to plug in your screwdriver. Namely, you will want to remove the screen filter from the shower head and it is best to find a perfect way to do it.
Therefore, you will need to find some kind of opening in the line where a shower head and screen filter meet.
Step 3 – Gently pry the filter screen and the rubber gasket
For this step, you will need to use a screwdriver.
First of all, you will need to gently pry the flow screen and detach it from the shower head. Once you do that, do the same with the rubber gasket and you’ll be able to see the flow restrictor.
However, you’ll most likely damage these parts if you don’t do this slowly and with patience. Therefore, make sure to be as careful as you can.
Step 4 – Locate the flow restrictor
Once you remove the screen filter and the rubber gasket, the only thing you’ll see is the flow restrictor.
The flow restrictor is usually a small part of the shower head and it stands in the middle of the pipe, at the center of the shower head.
By finding it, you will be able to remove it. So, let’s go to the next step.
Step 5 – Press one side of the flow restrictor with the screwdriver
Use a screwdriver and press it slowly on the side of the flow restrictor. This will make the flow restrictor to pop out on the opposite side and that’s where you will be able to remove it.
So, just press it slowly until one side of the flow restrictor lifts up.
Step 6 – Remove it slowly from the Peerless shower head
The next thing to do is to take the screwdriver and put it just under the part of the flow restrictor that is lifted a little bit.
Once you do that, it’s quite easy to remove the flow restrictor from the place where it’s located.
However, do this step slowly as well since you don’t want to damage this part, it’s quite important.
Step 7 – Put gasket rubber and the filter screen back inside
Once you did everything as we explained above, it’s time to put everything back in its place and reinstall the shower head back to the faucet.
So, first things first, the rubber gasket and the screen filter should be the first thing that you put back on the shower head.
Make sure to do it properly since these parts are actually quite fragile and they can easily break.
Step 8 – Reinstall the Peerless shower head on the faucet
As you reassembled the shower head back together, it’s only left to attach it back to the faucet once again.
This step is actually quite easy as you need to just screw the shower head back to the faucet as you removed it.
However, make sure to tighten it properly as you don’t want to experience any leaks.
Conclusion: Removing the Flow Restrictor from the Peerless Shower Head
As we can see, the removal of the flow restrictor from a Peerless shower head isn’t that big of a deal. All you have to do is to gather some tools and follow these steps. Make sure to do everything as we explained and you will be just fine.
We surely hope that this helped you to remove a flow restrictor and to improve your water pressure. If not, click on the banner below for help.
